Sprinkler and Drip Irrigation Installation
How an installer designs drip and sprinkler zones, what a smart controller does, and what to ask before the November winter blowout.

A yard watered on a guess shows it twice: in summer, when shrubs drown while the lawn browns, and in November, when water left in the lines can freeze and split a pipe. Five questions keep the guess out of the plan, and the blowout is the reason to ask them now. Put them to any installer before the first hard freeze:
- How many zones will my yard get, and what is in each one?
- Which areas get drip, and which get spray heads or rotors?
- What are my water pressure and flow rate, and how did you measure them?
- Will the controller be a WaterSense labeled smart model, and who programs it?
- Who winterizes the system, and does that include the backflow preventer?
The sections below explain each one in the order an installer thinks. This guide sits under our Building the Backyard pillar, where the rest of the outdoor build lives.
Drip vs Sprinkler Zones
An irrigation installer rarely picks one. Rain Bird's design guidance pairs rotors with large open lawns, spray heads with small areas, and drip with beds, shrubs and trees, and keeps drip and spray on separate zones.
Gene Caballero of GreenPal, a lawn care company, makes the same point from the plant side: shrubs, beds, containers and lawn want different amounts of water, and mixing them on one zone means some get too much and some too little. So the answer to question two is usually a map, not a choice.
How Irrigation Zones Are Designed
A design starts on paper: a to-scale drawing of the lawn, beds, patio, trees and the water supply line. Then comes the part you can't see from the patio. Rain Bird says water pressure and flow rate drive the layout, and its low-tech flow test is timing how long a five-gallon bucket takes to fill at an outdoor spigot.
A zone is a group of heads on one valve, sorted by plant type and sun exposure, and most backyards need two to four. Heads are placed for head-to-head coverage, so each sprinkler reaches the next one.
Ryan Kilsby of Waterworks Irrigation, an irrigation company, describes the planning in three parts: divide the yard into zones, know your flow or pressure, and know your municipal regulations.
Smart Irrigation Controllers
Most in-ground systems still run on a clock. A weather-based controller uses local weather and landscape conditions to set how much, how often and when to water, and it can replace the clock or work as an add-on. EPA says that swap can save an average home nearly 7,600 gallons a year.
The other WaterSense type is the soil moisture sensor, which overrides the schedule when the ground is already wet. The catch is the installation: EPA says these controllers need proper installation, programming and maintenance to beat a clock. That is why question four asks who programs it. Some utilities offer rebates.
Winterizing and Sprinkler Blowout
University of Minnesota turf staff say the safest winterizing is done by a certified irrigation professional. Consumer compressors reach the needed pressure but lack the air volume of commercial ones. SiteOne says an average residential system takes about 30 to 45 minutes. The order of the day:
- Run each zone and check for leaks or broken heads.
- Shut off the irrigation water between the supply and the backflow preventer.
- Blow out with an air compressor, starting with the zone farthest away and running each zone twice in short cycles.
- Turn the backflow preventer's ball valves to 45 degrees.
- Insulate exposed pipe and leave the controller off.
Steps one and two are fair work for a homeowner. Step three is where the installer earns the visit.
How to Hire an Irrigation Installer
Start with credentials and a few checks:
- Look for a WaterSense certified or Irrigation Association certified pro, as UMN suggests.
- Read Smartscape's Know Your Pro page for certifications and questions to ask.
- Expect a specialist or a local supply store's design service to cost more up front; Water Use It Wisely says it pays off.
- Try Rain Bird's free design service, which turns your scale drawing into a plan.
Kilsby's own advice is short. Hire an installer whose warranty covers parts and labor, he said, and have them teach you how to shut off the irrigation water and run the timer.
Highlights
How many zones does a backyard irrigation system need?
Rain Bird says most backyards need two to four zones, grouped by plant type and sun exposure, with drip and spray kept in separate zones.
Can I blow out my own sprinkler system?
The University of Minnesota says consumer compressors lack the air volume of commercial ones, so blowout should be left to professionals. Homeowners can check zones for leaks and shut off the water supply first.
Does a WaterSense smart controller save water?
EPA says an average home that swaps a clock controller for a WaterSense weather-based one can save nearly 7,600 gallons a year. The controller still needs proper installation, programming and maintenance.
Sources
- Weather-Based Irrigation Controllers | US EPA
- Soil Moisture-Based Irrigation Controllers | US EPA
- WaterSense Labeled Controllers | US EPA
- How to Design a Sprinkler System for Your Backyard
- Properly preparing irrigation systems for winter | Turfgrass Science
- How to Winterize an Irrigation System - SiteOne
- Creating An Irrigation System For Your Home And Garden? We Asked Specialists For Advice
- Irrigation Systems & Design - Water Use It Wisely
