About
The Letter

LAMiamiNY

Design

Who Measures Custom Drapery Before the First Cut

What happens between a tape measure and drapes on the rod, told through the workrooms and designers who publish how they do it, plus questions to ask before you order.

Custom Drapery Measuring Steps and Questions. Long cream curtains with a subtle check hang on a rod at either side of a tall window overlooking a green garden, held back with tiebacks.
Photo: Nieuw~commonswiki, CC BY-SA 3.0, via Wikimedia Commons

A 100-inch rod takes 250 inches of fabric. That is the 2.5 to 1 fullness Drapery Rods Direct builds into its custom pinch pleat draperies, and it is why a pair of drapes costs more in cloth and time than the window seems to deserve. The one step you can take tonight comes earlier. For ceiling-to-floor drapes, Drapery Rods Direct advises measuring the height in several spots and keeping the shortest number. Then deduct for the rod and leave ½ to ¾ inch of floor clearance. Everything the workroom does afterward rests on that number.

Who Measures Custom Drapery

Before you order, find out who owns the measurements. Custom Window Treatments, Inc. says the installer should measure, and that jobs measured by the designer often end badly. The designer then passes the installer's measurements, notes and photos to the workroom, which may talk with the installer about special windows such as corner windows. In a Savannah Window Fashions guide for designers, the firm explains that with a fabrication-only workroom the designer is responsible for measuring, specifying and installing, so a measurement error is theirs. A full-service workroom typically makes the soft treatments, orders custom hard treatments, and measures and installs. Designer Sarah Gibson writes on Room for Tuesday that some workrooms won't work with non-trade clients, and those that do will make the client's design from the specs, measurements and fabric the client supplies.

Steps From Measure to Cut, Sew and Hang

No single workroom publishes every stage, so this sequence draws on three who describe theirs: Custom Window Treatments, Inc., designer Janet Lorusso, and a workroom owner whose blog post does not name them.

  1. Measure the window and the space around it, in several spots, and send notes and photos to the workroom.
  2. Draw and quote. The workroom owner describes scale drawings and sketches with fabric and trim samples. Lorusso, in her post on the well-dressed window, checks fabric stock and dye lot first, then sends a client proposal and work orders and gets cuttings approved.
  3. Order and wait. Custom hardware may take several weeks, and that workroom promises no delivery date until all materials are in house.
  4. Inspect on arrival: yardage, pattern, color, trim splices, hardware finish, rod length and bracket counts.
  5. Place the pattern before the first cut, pinning pleats into panels to see the finished look. Lorusso checks in with the workroom at this point to review it.
  6. Cut and sew, with the pattern matched at seams, panel to panel and window to window.
  7. Fold the finished panels, fan or flat, to train the fabric and reduce wrinkles.
  8. Install. Professional installers hang and dress the panels, steam and train them, tack the returns to the wall and check the mechanisms.

Fullness, Pleats and Stack

Fullness is how much fabric goes into a width. Savannah Window Fashions says it prefers 250%, fabric 2.5 times the opening width. A two prong pleat needs only 200%, while sheers, which have no lining, may look best at 300%. A Houzz contributor says in a piece on the case for custom that most home decor fabric is about 54 inches wide, and each width covers 20 to 30 inches of rod, depending on fullness and pleat style.

Pleat count and fullness also set the stack, the space panels take up when open, which matters if you want to keep the view. Drapery Rods Direct's example adds 30 inches of stack-back to an 84-inch window, for a 114-inch width. Pinch pleats gather into uniform folds that stack evenly on traversing rods. Savannah Window Fashions adds that ripplefold can be complicated and needs an experienced workroom partner.

Why Lining and Fabric Matter

The stake is the room itself. Lining shields the face fabric from sun, which extends the life of the drapery and protects furnishings from UV damage, according to Savannah Window Fashions. Interlining adds energy efficiency and sound reduction. Houzz's contributor advises matching the lining's fiber to the face fabric so both age alike and the hem doesn't bag after a decade. Busy patterns often need more yardage to match, and linen can grow several inches from temperature changes alone.

Hardware, Returns and Brackets

Lorusso says custom hardware is made to measure, while retail hardware adjusts to a range of sizes, which can cause visual and functional problems. Houzz advises choosing hardware when you order. Returns, the sides that turn back to the wall, are typically 3½ inches for a single treatment and 5½ inches for the outer of two layers, per Houzz. Drapery Rods Direct lists 4 inches for one rod and 6 for two, and notes that returns reduce light leakage. Many designers add at least 6 extra inches to finished width to allow for ring creep. Gibson recommends center brackets for long rods or heavy fabric, after seeing treatments sag or pull hardware off the wall.

Why Custom Drapery Takes Time

None of the sources above publishes a price per window, so this story gives none. What they do give is time. The workroom owner says time is the key cost factor, because getting size, proportion and pattern placement right can't be rushed. Their post notes that big box panels come in standard sizes, 54 inches wide and 84 or 120 inches long, and that patterns rarely align between packages. Drapery Rods Direct makes its pinch pleat draperies to order, ships them in 4 to 6 weeks, and does not take returns.

Questions to Ask Before You Order

  1. Who measures, and who answers for a measurement error?
  2. What fullness and heading are you quoting, and how much stack will it leave?
  3. How will the lining match the face fabric, and is there an interlining?
  4. Who checks the fabric and pattern placement before cutting?
  5. Is the hardware made to measure, and are center brackets included?
  6. When is delivery promised, and does it wait for all materials?
  7. Who installs, and will they steam and train the panels and review care and operation with you?

Gibson also suggests keeping your first measurements and the workroom order on hand when the installer arrives.

The Credits

  • Janet Lorusso, designer: checks stock and dye lot, writes proposals and work orders, reviews pattern placement, inspects the finished treatments and supervises installation
  • Sarah Gibson, designer: writes on specifying window treatments for Room for Tuesday
  • Custom Window Treatments, Inc., workroom: argues the installer should measure
  • Savannah Window Fashions, workroom: prefers 250% fullness and guides designers on choosing a workroom
  • Drapery Rods Direct, maker: custom pinch pleat draperies and hardware
  • Installer: hangs, dresses, steams and trains the panels, tacks returns, checks mechanisms

Hanging Day

On the last day the panels come out folded, fan or flat, to train the fabric. The installer hangs them and dresses the folds, steams out what the folding left behind, and tacks each return to the wall. Then they run the mechanisms and walk through care and operation with the owner. Gibson's advice is to style the curtains afterward, once they are up and hanging straight.

Highlights

How do you measure for floor-length drapes?

Drapery Rods Direct advises measuring the height in several places and keeping the shortest number, then deducting for the rod and leaving ½ to ¾ inch of floor clearance.

Who should measure for custom drapery?

Custom Window Treatments, Inc. says the installer should measure, and that designer-measured jobs often end badly. Savannah Window Fashions notes that with a fabrication-only workroom, measurement errors fall to the designer.

How much fabric do custom drapes need?

Savannah Window Fashions prefers 250% fullness, which is fabric 2.5 times the opening width. A two prong pleat needs only 200%, and sheers may look best at 300%.

More Stories

From LA Miami NY

A cabana daybed beside a rooftop infinity pool high above a curving bay, beaches and a city skyline
The Letter

Each new story from LA Miami NY, sent to your inbox when it is published. Nothing else. Leave any time.