Low Voltage Landscape Lighting
A low-voltage yard system is a transformer, cable and fixtures. Here is how to plan the layout, which part belongs to an electrician, and how to leave room for holiday lights.

Walk the yard after dark before anyone draws a plan. This Old House suggests walking the property at night to choose light placement for looks, function and safety, and steps and changes in elevation are where it counts. The rest of the layout follows from that walk, in this order:
- Mark what the night walk showed: steps, elevation changes, paths, and the walls or plants worth seeing.
- Find the nearest outdoor power source, which is where the step-down transformer will go.
- Add up the wattage of every fixture you listed.
- Pick a transformer and cable that cover that total with room to grow.
- Choose how the lights switch on.
- Test every light before the cable is buried or the fixtures are fixed in place.
It is the cheapest step in the job, and every drawing that comes after it is a guess without it.
Low-voltage lighting has three parts. The transformer converts 120-volt household power to a lower voltage; Big Frog Supply says it plugs into a standard outdoor outlet and puts out 12V or 15V. Cable carries that power across the yard, and fixtures sit at the end of each run.
Outdoors, EC&M's code explainer says these systems are capped at 15V, with most running at 12V, and that landscape systems are listed to UL 1838. The article is older, so ask whoever draws your plan to confirm against the code your city enforces today.
Start with the transformer. This Old House advises adding 20% to total fixture wattage, so a 100-watt system calls for at least 120 watts and next year's extra path light does not mean a new unit. Mount it at least 12 inches off the ground, sheltered but easy to reach. A model with a built-in timer or photocell brings the lights on at dusk; smart controls are the other option. EC&M adds that the number of lighting units must not exceed what the listing and product directions allow.
Then the cable. This Old House says 12-gauge suits most residential installs and limits voltage drop, while Big Frog Supply calls 12-gauge or 14-gauge standard for most DIY work. Brass barrel connectors hold up better than plastic. Burying cable is not strictly necessary, but about 6 inches deep protects it, and a small loop left at each fixture lets you move lights later.
Fixtures do different jobs. Lights on steps and elevation changes are safety work; a wall wash is for looks. If you care about the night sky, ask for shielded, warm fixtures. DarkSky's residential luminaire program, as LightNOW reported on March 19, 2024, requires full shielding, uplight of no more than 50 lumens, and a color temperature of 3000K or warmer (amber is also allowed), plus safety certification from an independent laboratory. Near a pool, EC&M says fixtures from these systems can't be run closer than 5 ft.
The sources draw one firm line on who does what. This Old House recommends a licensed electrician for 120-volt household wiring, and says a DIY 12-volt system should use a transformer that plugs into an outlet rather than one wired into the home. So if no weatherproof outdoor outlet sits near the transformer, that is the electrician's job. EC&M says the receptacle must stay weatherproof while the plug is connected, and a power unit marked "Outdoor Use Only" cannot be used indoors.
What the sources do not describe is a lighting designer's scope, and none of them names a local electrician or designer, so this story will not guess at one. Hire for the part that is yours to check: the written plan should show where the transformer sits and where its power comes from, total wattage with the 20% added, cable gauge and connectors, how the lights switch on, and what was tested before burial. For an electrician or a designer, that page is the thing worth paying for.
Holiday lights belong in the plan from the start, and the sources point to one cautious rule: do not assume the landscape transformer carries them. EC&M says a power supply's output must never be connected in series or parallel, and that unit counts cannot exceed the listing. Ask the electrician to put a weatherproof outdoor outlet near the roofline or tree you decorate, and to say in writing what the transformer can and cannot carry.
To keep the holidays easy, a short list for the electrician:
- A separate weatherproof receptacle at each decorated spot.
- A note of the transformer's listed limit, so nobody plugs past it.
- Slack cable and room at the transformer, so December work does not disturb the path lights.
At dusk the photocell does its work before anyone is home to see it. The path lights come up warm along the steps, a wall catches a little light, and the transformer sits quiet above the ground, a short way from the outlet. In December a second outlet, put there on purpose, feeds the line along the eave.
Highlights
Who installs the power for yard lighting?
This Old House recommends a licensed electrician for 120-volt household wiring. A DIY 12-volt system should use a transformer that plugs into an outlet.
How big should the transformer be?
Add up fixture wattage and add 20% for expansion. For a 100-watt system, that means at least 120 watts.
What cable do low-voltage lights use?
This Old House says 12-gauge suits most residential installs and limits voltage drop. Big Frog Supply says 12-gauge or 14-gauge is standard for most DIY projects.
